The AL series utilizes a fixed planet design, which allows the output housing of the gearbox to drive the pulley versus a standard shaft driven system. This new technology and design allows the pulley to be centered in between two high capacity bearings which increases stiffness and radial load capacities to over 2 times competitive models.

The True Helical gear design increases tooth-to-tooth contact ratio by over 33% vs. the standard spur gearing geometry. The Helix angle is optimized and produces smooth and quiet operation at extreme speeds. (Less than 2 arc-min, less than 56dB, up to 10,000rpms input).

The product is offered in 7 sizes (70mm thru 280mm) and is equipped with standard single & double stage ratios (2, 3, 4, 5, 6, 7, 8, 9, 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90). Covered by the industry leading 5-year tip to toe warranty and delivery is guaranteed with in two weeks or it’s FREE.

With traditional rack and pinion systems, the pinion gear teeth slide along the rack teeth as the pinion rotates. To reduce wear and friction, a small clearance is required between the rack teeth and pinion teeth. Depending on the application, this may introduce too much inaccuracy. For higher accuracy, a ballscrew might be used, but ballscrews have a limited length and speed. Linear motors address the speed and length issue, but the cost of long magnet tracks can be prohibitive.

The RPS system addresses the accuracy and wear issues by using bearing supported rollers and a special rack tooth profile. The rollers meet each tooth along a tangent path and smoothly roll down the tooth face, as opposed to a pinion which slaps into the tooth and then slides down its face. This increases life and lowers noise. The tooth profile is designed so that two rollers are loaded in opposition at all times, providing zero backlash.

The RPS system can achieve speeds up to 11 m/s and provide dynamic thrust up to 14000 N (3150 lbf). Racks can be assembled together in 0.5 and 1 meter increments, allowing unlimited travel lengths. As shown with the sample data below, the system’s accuracy is better than +/- 30 microns and does not vary with travel distance.

The video below shows the RPS system in action.

The AZ series is designed to drive brushed and brushless servo motors. To increase system reliability and to reduce cabling costs, the drive is designed for direct integration into your PCB. The drive interfaces with digital controllers that have analog +/-10V output. It requires only a single unregulated isolated DC power supply, and is fully RoHS (Reduction of Hazardous Substances) compliant.

The drive is available with peak current capability up to 40 A and continuous current up to 20 A. It supports voltages from 10 to 80 VDC. Options are available for torque control and velocity control with hall or encoder feedback.

Each compact RIO-471×0 is self contained with numerous analog and digital I/O points. Multiple RIO-471×0 units can be distributed on an Ethernet network, allowing I/O expansion.

The RIO-471×0 is fully programmable, making it much more than a remote I/O slave. With concurrent execution of up to four application programs, closed-loop PID control of analog process control loops, and the capability to control other devices as a Modbus master, the RIO-471×0 series brings Galil’s expertise in rapid and cost-effective development of motion control systems to the machine control world.

Standard features include:

• 10/100 Base-T Ethernet port
• RS232 port configurable for 115 or 19.2 kbaud
• 8 analog inputs and 8 analog outputs
• 16 optically isolated inputs
• 8 high-power, isolated outputs rated at 500 mA per output
• 8 isolated outputs rated at 25 mA max per output
• 2 analog process control loops controlled by Galil PID filter
• Concurrent execution of up to four application programs
• LED indicators for all digital I/O points
• Easy-to-use, 2-letter Galil programming language

The PE series uses fully supported planet gearing and thicker planet gears to increase the tooth-to-tooth contact ratio, resulting in torque capacities over 30% higher than other standard spur gearing geometry. The gearing is optimized and produces smooth and quiet operation at extreme speeds. At up to 8000 RPM input speed, noise is held under 68 dB while backlash is less than 6 arc-min.

The product is offered in 5 sizes from 50 mm to 155 mm and is equipped with single stage ratios of 3,4,5,7, and 10:1 along with 9 more double stage ratios of from 15:1 to 100:1. Other options in the PE series are Square Metric (PB) and English Nema (PN), all of which are available from stock.

The PE series gearboxes are covered by Apex’s industry leading 2-year tip to toe warranty. Delivery is guaranteed within two weeks or the gearboxes are free.

Linear Motioneering users enter application parameters including mounting configuration, environmental conditions, positioning, loading and move requirements. With that information, the system recommends a choice of specific systems optimized to meet the demands of the particular application. The recommended product solution, including any accessories and motor mounts, is assigned a Smart Part Number that the machine builder can use to order the linear motion system with all accessories pre-mounted and ready for integration into the machine.

A motor interface selector allows users to enter motor dimensions, or any major manufacturer’s motor model number, and the system automatically configures the mating flange and coupling. Linear Motioneering also provides safety factors for critical system components that allows users to make a decision based not just on price, but on the safety margin of his or her selection. Users can change the move profile and calculate the resulting loads and safety factors on the fly. An environmental screen guides the user not only to the base system selection, but also displays appropriate options such as material and coatings that are suitable for that environment.

Linear Motioneering also includes a Configure Your Solution mode which provides all of the same deliverables as the Sizing and Selection mode, but is intended for those who are familiar with Danaher Motion products and want to quickly configure a part number. The Lookup by Part Number module is a way for repeat customers to confirm current pricing and part number configuration.